{"id":265055,"date":"2023-08-01T02:48:33","date_gmt":"2023-08-01T02:48:33","guid":{"rendered":"https:\/\/transact-tech.com\/service-and-support\/?p=265055"},"modified":"2024-02-08T18:30:27","modified_gmt":"2024-02-08T18:30:27","slug":"how-to-load-labels-into-your-boha-terminal","status":"publish","type":"post","link":"https:\/\/transact-tech.com\/service-and-support\/2023\/08\/01\/how-to-load-labels-into-your-boha-terminal\/","title":{"rendered":"How To Load Labels Into Your BOHA! Terminal"},"content":{"rendered":"\n

With your BOHA! Terminal powered on, grab hold of the two tabs at either side of the lower section of the display and pull up . The hinged display will make a click sound and you will be able to swivel the display up until it is parallel with your tabletop.\u00a0 The one or two label printer mechanisms and label buckets will be visible, depending on your configuration.\u00a0 The BOHA! Terminal uses thermal printing technology, so no ink or toner is required.<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n

ft. The top of the printer mechanism will open.<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n

Both mechanisms can handle narrow and wide labels.\u00a0 In this example (your labels may differ in size or style) place the roll of 2 .2\u201d x 2\u201d labels into the left printer label bucket and then the 1 .2\u201d x 1\u201d labels in the right printer label bucket. Make sure the labels feed from the top.<\/p>\n\n\n\n

Note:<\/strong> If unpacking the labels has resulted in any of the leading labels being pulled off the roll, leaving a blank space, trim the roll to eliminate the gap. Otherwise the gap from the missing label can cause your printer to stop printing, requiring you to re-set the label roll.<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n

Next, thread the labels under the label sensor as shown below. Notice that the 1 .2\u201d wide labels will slide only part of the way under the sensor because they need to remain centered with the roll, while the 2 .2\u201d wide labels will slide all the way under the label sensor to the left edge.<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n

Then close the latch of the printer mechanisms. There will be some movement of the labels after you close the latch and the labels align for printing.\u00a0 Now you are ready to close the display.\u00a0 Rotate the hinged display down until it clicks to its closed position.<\/p>\n\n\n\n

\"\"<\/figure>\n","protected":false},"excerpt":{"rendered":"

With your BOHA! Terminal powered on, grab hold of the two tabs at either side of the lower section of the display and pull up . The hinged display will make a click sound and you will be able to swivel the display up until it is parallel with your tabletop.\u00a0 The one or two […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_et_pb_use_builder":"off","_et_pb_old_content":"","_et_gb_content_width":"1080","_relevanssi_hide_post":"","_relevanssi_hide_content":"","_relevanssi_pin_for_all":"","_relevanssi_pin_keywords":"","_relevanssi_unpin_keywords":"","_relevanssi_related_keywords":"","_relevanssi_related_include_ids":"","_relevanssi_related_exclude_ids":"","_relevanssi_related_no_append":"","_relevanssi_related_not_related":"","_relevanssi_related_posts":"","_relevanssi_noindex_reason":"","_coblocks_attr":"","_coblocks_dimensions":"","_coblocks_responsive_height":"","_coblocks_accordion_ie_support":"","footnotes":""},"categories":[165,230],"tags":[],"class_list":["post-265055","post","type-post","status-publish","format-standard","hentry","category-boha-terminal","category-boha-terminal-support-topics"],"_links":{"self":[{"href":"https:\/\/transact-tech.com\/service-and-support\/wp-json\/wp\/v2\/posts\/265055","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/transact-tech.com\/service-and-support\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/transact-tech.com\/service-and-support\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/transact-tech.com\/service-and-support\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/transact-tech.com\/service-and-support\/wp-json\/wp\/v2\/comments?post=265055"}],"version-history":[{"count":0,"href":"https:\/\/transact-tech.com\/service-and-support\/wp-json\/wp\/v2\/posts\/265055\/revisions"}],"wp:attachment":[{"href":"https:\/\/transact-tech.com\/service-and-support\/wp-json\/wp\/v2\/media?parent=265055"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/transact-tech.com\/service-and-support\/wp-json\/wp\/v2\/categories?post=265055"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/transact-tech.com\/service-and-support\/wp-json\/wp\/v2\/tags?post=265055"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}