RS232 Serial Communications Interface PCB
The RS232 Serial interface connector is a 14 position Molex Minifit Jr®., part number 39-30-1140,
which mates with Molex part number 39-01-2140 or equivalent.
Serial Communication PCB Pin-Outs
| PIN# | FUNCTION | I/O |
| 1 | MREST (Active Low) | I |
| 2 | Not Connected | N/C |
| 3 | +12 VDC | I |
| 4 | Not Connected | N/C |
| 5 | GND | – |
| 6 | +24 VDC | – |
| 7 | GND | – |
| 8 | +24 VDC | – |
| 9 | Bezel Lamp – Switched +24 VDC | O |
| 10 | FGND | – |
| 11 | RS232 RXD | I |
| 12 | RS232 TXD | O |
| 13 | DTR | O |
| 14 | RTS | O |
Default Communication Settings
The RS-232C interface default configuration settings are:
Baud Rate: 9600 BPS
Data Bits: 8 Bits
Parity: None
Stop Bits: 1
Handshaking: XON/XOF
Receive Error: Prints
Input Buffer 8,192 bytes
These communications settings may be altered only through the use of the CONFIG program, special printer
configuration software available from TransAct. Contact TransAct Technical Support for further information
on this utility.
USB Communications Interface PCB
The USB Communications PCB contains two connectors.
- Power – 4 position Molex Minifit Jr®., part number 39-30-1040, which mates with Molex
part number 39-01-2040 or equivalent.
- USB Communications – Type B USB connector
USB Communications PCB Pin-Outs
| USB Connector | ||
| PIN # | FUNCTION | I/O |
| 1 | VBUS | – |
| 2 | D- | I/O |
| 3 | D+ | I/O |
| 4 | GND | – |
| Power Connector | ||
| PIN # | FUNCTION | |
| 1 | +24 VDC | – |
| 2 | GND | – |
| 3 | GND | – |
| 4 | FGND | – |
NETPLEX Communications Interface PCB
The NETPLEX Communications interface connector is a 10 position Molex Minifit Jr®., part number 39-30-1100,
which mates with Molex part number 39-01-2100 or equivalent.
NETPLEX Communication PCB Pin-Outs
| PIN # | FUNCTION | I/O |
| 1 | MREST (Active Low) | I |
| 2 | RXD | I |
| 3 | +12 VDC | I |
| 4 | TXD | O |
| 5 | SGND | – |
| 6 | +24 VDC | – |
| 7 | GND | – |
| 8 | +24 VDC | – |
| 9 | Bezel Lamp – Switched +24 VDC | O |
| 10 | GND | – |
Universal USB/NETPLEX Communications Interface PCB
The Universal USB/NETPLEX interface supports both USB and NETPLEX communications.
This interface contains three connectors:
- Power – 4 position Molex Minifit Jr®., part number 39-30-1040, which mates with Molex
part number 39-01-2040 or equivalent.
- NETPLEX communications- 6 position Molex Minifit Jr®., part number 39-30-1060, which mates with
Molex part number 39-01-2060 or equivalent.
- USB Communications – Type B USB connector.
Universal USB/NETPLEX Communication PCB Pin-Outs
USB Connector
| PIN # | FUNCTION | I/O |
|---|---|---|
| 1 | VBUS | – |
| 2 | D- | I/O |
| 3 | D+ | I/O |
| 4 | GND | – |
Power Connector
| PIN # | FUNCTION | I/O |
|---|---|---|
| 1 | +24 VDC | – |
| 2 | GND | – |
| 3 | GND | – |
| 4 | FGND | – |
NETPLEX Connector
| PIN # | FUNCTION | I/O |
|---|---|---|
| 1 | MREST (Active Low) | I |
| 2 | RXD | I |
| 3 | +12 VDC | I |
| 4 | TXD | O |
| 5 | SGND | – |
| 6 | Bezel Lamp – Switch +24 VDC | O |
Dual Port NETPLEX Communications Interface PCB
The Dual Port NETPLEX Communications interface contains three connectors:
- NETPLEX Communications. – 10 position Molex Minifit Jr®., part number 39-30-1100 for NETPLEX
connections which mates with Mole part number 39-01-2100 or equivalent.
- I2C Communications – 2 modular RJH connections The connectors are electrically connected to allow daisy
chaining of multiple devices.
NETPLEX Communication PCB Pin-Outs
| PIN # | FUNCTION | I/O |
|---|---|---|
| 1 | MREST (Active Low) | I |
| 2 | Not Connected | N/C |
| 3 | +12 VDC | I |
| 4 | Not Connect | N/C |
| 5 | GND | – |
| 6 | +24 VDC | – |
| 7 | GND | – |
| 8 | +24 VDC | – |
| 9 | Bezel Lamp – Switch +24 VDC | O |
| 10 | GND | – |
I2C Port
| PIN # | FUNCTION | I/O |
|---|---|---|
| 1 | RESET | I |
| 2 | SCL | I |
| 3 | SDA | I/O |
| 4 | GND |
Dual Port RS232 Communications Interface PCB
The Dual Port RS232 Communications interface contains three connectors:
- RS232 Communications14 position Molex Minifit Jr®., part number 39-30-1140 which mates with Molex
part number 39-01-2040 or equivalent.
- I2C Communications -2 two modular RJH connections for a secondary I2C port. The two modular connectors
are electrically connected to allow daisy chaining of multiple devices.
NETPLEX Communication PCB Pin-Outs
RS 232 Connector
| PIN # | FUNCTION | I/O |
|---|---|---|
| 1 | MREST (Active Low) | I |
| 2 | Not Connected | N/C |
| 3 | +12 VDC | I |
| 4 | Not Connected | N/C |
| 5 | GND | – |
| 6 | +24 VDC | – |
| 7 | GND | – |
| 8 | +24 VDC | – |
| 9 | Bezel Lamp – Switch +24 VDC | O |
| 10 | FGND | – |
| 11 | RS232 RXD | I |
| 12 | RS232 TXD | O |
| 13 | DTR | O |
| 14 | RTS | O |
I2C Port
| PIN # | FUNCTION | I/O |
|---|---|---|
| 1 | RESET | I |
| 2 | SCL | I |
| 3 | SDA | I/O |
| 4 | GND |
Bezel Lamp Connector
The bezel connector is a Molex Minifit Jr®, part number 39-01-4032 and will mate with a Molex
part number 39-01-4030 or equivalent.
Bezel Lamp Connector Pin-Outs
| PIN # | FUNCTION |
|---|---|
| 1 | Modulated +24VDC |
| 2 | Not Connected |
| 3 | GND |